Stanley laser RL HVPW Manual

PDF Manuals
310 Pages English

Stanley laser RL HVPW
16
77-496 / 77-429 / 77-439 / 77-497 / 77-427
• There is no need to adjust calibration if the distance
between reference point “D
1
” and “D
2
” is < 2,0 mm.
• If the distance measured is ≥ 2,0 mm then a calibration
adjustment is necessary.
• Perform the same steps for the “Y” axis as was done
for the “X” axis. Replace “X1” and “X2” with Y1” and
“Y2”
(
N
4
).
Horizontal Calibration (See Figure
N
)
(For RL HW substitute
where ever is
referenced below)
(For RL HW / RL HW+ substitute
where ever
is referenced below)
• With laser tool powered OFF, press and hold
followed by
.
• Release
and continue to hold for ≥ 3
seconds.
• Release
.
• The LED/LCD will indicate laser tool is in Calibration
mode.
• If necessary, adjust the “X” axis by pressing
until the laser beam is aligned with “D
0
”. “D
0
” is the
halfway point between
“D
1
” and “D
2
” during “X” axis
check.
• Press again to set the “X” axis and / or proceed to
the “Y” axis adjust.
• If necessary, adjust the “Y” axis by pressing
until the laser beam is aligned with “D
0
”. “D
0
” is the
halfway point between
“D
1
” and “D
2
” during “Y” axis
check.
• Press again to set the “X” axis and / or proceed to
• Reference Figure
L
for resulting slope direction for
each key.
Remote Control
• The same functions / modes for each specifi c laser tool
are accessible through use with the keys available on
the remote.
• The laser tool can be powered OFF with the remote by
pressing both
at the same time. The laser tool
can only be powered ON with the power key on the
laser tool.
Accuracy Check and
Calibration
NOTE:
• See Feature Set to reference which models offer specifi c
functions.
• The laser tools are sealed and calibrated at the factory to
the accuracies specifi ed.
• It is recommended to perform a calibration check prior to
its fi rst use and then periodically during future use.
• Be sure to allow the laser tool adequate time to Auto-Level
(< 60 seconds) prior to a calibration check.
• The laser tool should be checked regularly to ensure its
accuracies, especially for precise layouts.
Horizontal Check (See Figure
N
)
• Set the laser tool on a tripod 20 m away from a wall
with the ”X1” side facing the wall (
N
1
).
• Power ON the laser tool and allow the laser tool to
Auto-Level and be sure laser is rotating.
• Go to the wall and mark a reference point “D
1
” where
the laser line is on the wall. If available, using a
detector may help in locating the beam more easily.
• Loosen the laser tool from the tripod and rotate the
laser tool 180° so that the “X2” side is now facing the
wall (
N
2
).
• Go back to the wall and measure the distance between
the fi rst reference point “D
1
” and the second reference
point “D
2
” (
N
3
).
Related Manuals for Stanley laser RL HVPW
CL2XTi
Stanley laser CL2XTi

For laser (166 Pages)
TLM165 - STHT1-77139
Stanley laser TLM165 - STHT1-77139

For laser (13 Pages)
TLM165i - STHT1-77142
Stanley laser TLM165i - STHT1-77142

For laser (13 Pages)
CL2i
Stanley laser CL2i

For laser (148 Pages)
TLM220i - 77.116
Stanley laser TLM220i - 77.116

For laser (22 Pages)
RL HGW
Stanley laser RL HGW

For laser (310 Pages)
MultiLine 77-122
Stanley laser MultiLine 77-122

For laser (174 Pages)
STHT77341 - Cross 90
Stanley laser STHT77341 - Cross 90

For laser (210 Pages)
SCL-D
Stanley laser SCL-D

For laser (208 Pages)
RL HW
Stanley laser RL HW

For laser (310 Pages)
RL HV
Stanley laser RL HV

For laser (310 Pages)
CL90i
Stanley laser CL90i

For laser (164 Pages)
TLM99
Stanley laser TLM99

For laser (10 Pages)
SLP3
Stanley laser SLP3

For laser (212 Pages)
FMHT77356
Stanley laser FMHT77356

For laser (208 Pages)